| Error Code | Description |
|---|
| 0 | BAT_SCP: Short circuit protection triggered (main battery) |
| 1 | BAT_MOTP: MOSFET over-temperature protection activated (main battery) |
| 2 | BAT_PDSCP: Pre-discharge short circuit protection triggered (main battery) |
| 3 | BAT_PDOCP: Pre-discharge overload circuit protection triggered (main battery) |
| 4 | BAT_UVP2: Under-voltage protection level 2 activated (main battery) (charge longer to resolve) |
| 5 | BAT_UVP1: Under-voltage protection level 1 activated (main battery) |
| 6 | BAT_OVP2: Over-voltage protection level 2 activated (main battery) |
| 7 | BAT_OVP1: Over-voltage protection level 1 activated (main battery) |
| 8 | BAT_COCP1: Charge over-current protection level 1 triggered (main battery) |
| 9 | BAT_COCP2: Charge over-current protection level 2 triggered (main battery) |
| 10 | BAT_DOCP2: Discharge over-current protection level 2 triggered (main battery) |
| 11 | BAT_DOCP1: Discharge over-current protection level 1 triggered (main battery) |
| 12 | BAT_CUTP: Charge temperature too low to operate (main battery) |
| 13 | BAT_COTP: Charge temperature too high to operate (main battery) |
| 14 | BAT_DUTP: Discharge temperature too low to operate (main battery) |
| 15 | BAT_DOTP: Discharge temperature too high to operate (main battery) |
| 16 | BAT_FP: Permanent failure detected (main battery) (likely due to a blown fuse or socket short) |
| 17 | BATTERY_NO_DSG: Unable to enable discharge mode (main battery) |
| 18 | BATTERY_MISSING: Battery signal missing (main battery) (battery not recognized or not present) |
| 19 | BATTERY_COMMUNICATION: Communication error with the battery (main battery) |
| 20 | BATTERY_NO_OUTPUT: Battery management system (BMS) shut down detected (main battery) |
| 21 | NO_CHARGE_CURRENT: Charging state active, but no current detected (main battery) |
| 22 | MOTOR_COMMUNICATION: Communication issue with the SSP TI motor chip (module related) |
| 23 | BLE_COMMUNICATION: Communication issue with the Bluetooth chip (module related) |
| 24 | OAD_ABORT: Over-the-air download (OAD) transfer aborted (module related) |
| 25 | OAD_CRC: CRC error detected in transferred image (module related) |
| 26 | OAD_TRANSFER: Over-the-air download transfer took too long (module related) |
| 27 | OAD_PACK: Invalid or missing file in the package (module related) |
| 28 | ICF_TIMEOUT: Timeout occurred during flash programming (module related) |
| 29 | ICF_HEADER: Flash header not found (module related) |
| 30 | ICF_NO_FILES: No files detected in the package (module related) |
| 31 | ICF_ERASE: Flash memory erase failed (module related) |
| 32 | ICF_WRITE: Flash memory write failed (module related) |
| 33 | ICF_CRC: CRC error in a file within the package (module related) |
| 34 | PGM_MOTORWARE: Motor controller programming failed |
| 35 | PGM_BATTERYWARE: Battery management system (BMS) programming failed |
| 36 | PGM_SHIFTERWARE: Shifter controller programming failed |
| 37 | PGM_BLEWARE: Bluetooth controller programming failed |
| 38 | INTERNAL_BATTERY: STVC3115 read error, internal LiPo battery might be missing (module related) (check charging) |
| 39 | READ_LIGHT_SENSOR: Error reading the CM3232 light sensor (module related) |
| 40 | STUCK_HORN_BUTTON: Horn button pressed or stuck for too long (water damage or short circuit possible) |
| 41 | STUCK_BOOST_BUTTON: Boost button pressed or stuck for too long (water damage or short circuit possible) |
| 42 | KL_COIL_MISSING: Kick-Lock coil not detected |
| 43 | SHIFTER_NOT_IN_GEAR: Shifter unable to reach the desired gear after 10 attempts |
| 44 | SHIFTER_COMMUNICATION: Communication issue with the shifter (module related) |
| 45 | MOTOR_MOTOR_CABLE: Motor cable disconnected or not recognized |
| 46 | MOTOR_MOTOR_OVER_CURRENT: Over-current detected in motor driver |
| 48 | MOTOR_CONTROLLER_ERROR: Error in motor controller parameters (motor replacement recommended) |
| 49 | MOTOR_CURRENT_ERR: Current offset calculation deviated from default |
| 50 | MOTOR_VOLTAGE_ERR: Voltage offset calculation incorrect (Vbat/2 or Vbat deviation) |
| 51 | MOTOR_DERATING: Motor performance limited due to high temperature |
| 52 | MOTOR_TORQUE_SENSOR_FAIL: Torque sensor failure detected |
| 53 | MOTOR_NOT_READY: Motor not ready during testing or operation |
| 54 | NO_SIMCARD: SIM card missing or not recognized (module related) |
| 55 | I2C3_FAIL: Error detected on I2C bus 3 during startup |
| 56 | CCID_SIMCARD: SIM card CCID number mismatch (VanMoof-specific SIM required) |
| 57 | READ_SIMCARD: SIM card detected but not communicating (check ICCD number) |
| 58 | GSM_MODEM: GSM modem startup failed (usually resolves after a reset) |
| 60 | FACTORY_MODE: Factory firmware detected (display shows error code 60) |